Just How to Remove as Well as Change a Tub
Just How to Remove as Well as Change a Tub
Blog Article
We have stumbled upon this great article on How to Install a Bathtub listed below on the internet and decided it made perfect sense to talk about it with you over here.
Mounting a tub isn't precisely rocket science, however it does call for solid plumbing, carpentry, and occasionally, tiling abilities. Changing an old tub with a new one is likewise a reasonably tough project. If the old tub is readily accessible, the project can relocate speedily; if you need to open up a wall surface to eliminate the old tub as well as position the brand-new bath tub, the job is much harder. In either case, the job is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub as well as set in the new one. Make certain you have actually qualified yourself for the job and also fit trying it. Instead of hiring a professional to take control of a halfway-completed job, it is better to consider employing one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This article will certainly assist you set up a new bathtub in your bathroom if you have actually currently bought a brand-new bathtub and do not require to change the setup of your previous water system pipes.
Your devices as well as material list ought to comprise the following:
Planning for the Setup
Firstly, the sustaining framework provided with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the tap includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to avoid pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome as a result of the limited access that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the staying water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wood boards are practical in equally spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the spirit level and readjusting the feet on the tub until the spirit level reviews degree.
To mount faucets, fit the bottom of the outermost versatile tap adapter to the ideal supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Activate the water system as well as inspect all joints and new pipework for leaks and tighten them if essential. Fill the tub as well as additionally inspect the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, fix the bath paneling as described in the supplier's user's manual. Tiling and securing around the tub should wait till the bathtub has actually been utilized at least when as this will resolve it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making sure that the washing machines are in location in between the tap and the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous type ought to be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a rigid seal, creating the water to penetrate the wall between the bath and also the tiling, causing problems with moisture and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to assimilate your components and fittings. They are offered in tubes as well as cartridges, and also can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water before sealing, to allow for the motion experienced when the tub is in use. The sealant can fracture fairly early if you do not take into consideration this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our article about How to Install a Bathtub. Many thanks for spending some time to read through our piece of content. Appreciated our article? Please share it. Help other people discover it. Thanks a lot for your time. Kindly come by our site back soon.
Click On This Link
Report this page